Related part should be operated under low voltage condition. All installation process and maintainance should be carried out by the supplier.
Name of Related Parts
▪JST connection ( Red: 24V power cable; Yellow: Relay )
▪COM / NO
▪The incator will shin for few seconds when starting. When object is detected by sensor, indicator lights up.
▪Fluctuation up and down, rotation left and right.
1.Please do the installation in the proper position. Installation height within 3.5m. Please arrange hole(Φ3.2mm)on the installation module. And hole(Φ12m) for insetting guide line.
2. Please connect the signal cable with the terminal of automatic door.
Brown and Yellow cable: AC/DC12V-24V
Green and White cable: Signal output COM/NO
3.Take the outer cover off, and fix the screws.
4.Finish the cable connection and get on power.
5.Please set the detection range and disjunctor accordingly
6.Cover with the lid
Adjustment ( Get on Power )
: Please stand out of the detection range around 5s to ensure the sensor has enough time to finish the self-adjustment.
Select different detection range by adjusting sensitivity knob
3.Adjustment of detection direction
( Adjust Direction of front and back/Left and Right flexibly )
Adjusting angle of plain aerial to get different detection distance and range 30=15×2rangeNOTE
Intial setting is degree by factory.
All the parameters above are only for reference, detection height is 2.2M.
Detection range will be different because of the making material of door and ground, please adjust the sensitivity by the knob mentioned above.
When it is adjusted to 60 degree, the detection range is the widest, door will keep on closed and open aii the time.
▪Position should be fixed tightly to avoid vibrating.
▪Do not place into board or other material.
•Moving object should be avoided.
▪Fluorescent should be avoided.
▪Do not touch directly ESD Protections necessary.
Picture of Automatic Sliding Doors Infrared Microwave Sensor
The Internal Structure
|Door&Indicator lose failure||Did not get on power||Check cable connection & power supply|
|Door keep on closed and open||Sensor detected the movement of autodoor, vibration of movement||1.Adjust angle|
2.Check the position
|Door do not close Red indicator lose failure||1.Switch of autodoor controller lose failure|
3.Incorrect output of sensor
|Check the switch of autodoor controller & setting of output|
|Door keeps on moving when it rains||Sensor detected the actions of rain||Adopt waterproof accessories|
Technology: Microwave & microwave disposer
Transmitting power:<20dBm EIRP
Installation height: 4M(MAX)
Detection mode: Moving
Maximum voltage: 42V AC-60V DC
Maximum switching power: 30W(DC)/60VA(AC)
Guide line: 2.5M
Protection class: IP54
Anti-interference performance: R & TTE 1995/5/EC, EMC 89/366/EEC
Power voltage: 12V TO 30V AC+/-10% ( 50Hz to 60 Hz ): 12V to 36V DC
Frequency: 24, 125GHz
Launch frequency density:<5mW/cm²
Installation angle: 0-90 degree( lengthways )-30 to+30(lateral)
Min detection speed: 5cm/s
Detection range: 8m*4m( Installation height: 2.2M )
Maximum current: 1A
Retension time: 0.5s
Working temperature: -20ºC to +55ºC
Sheating material: ABS plastic
Pictures of Automatic Doors
Other Accessories of Automatic Doors
The automatic door operator is to be fully electronic operator, housed in a fully anodised aluminum transom section.
The intelliget controller unit can be programmed for connection to any security/alarm systems, is self monitoring and calibrating, has memory for all data on door stoke and brake positions.
The operator has built-in uninterrupted power supply (Battery back up) operation and security during power failure.
Drive is by way of toothed belt, which is reinforced with fiberglass tensile members, and has nylon facing surface for tooth protection on the pulleys. This combination produces silent accurate operation.
The track is self-cleaning duel linear. The upper track is made of harder stronger alloy 6351T6, and can be replaced without moving the transom. The wheel trolley is fitted with anti-rise wheels, resulting in very firmly fitted doors with operation free of any racking.
Electromechanical Locking: An electric lock option is available to give total security and can be adapted where manual locking cannot be achieved, i. E. Frameless toughened Glass doors. Lock is the microprocessor controlled electric locking system. The microprocessor monitors all aspects of the lock functions. E. G. To ensure the door is fully closed when the lock is 100% engaged. Terminal outputs are available to signal to security system both door positions and lock status.